AB and BC are the two most common quality grades for Siberian larch decking boards. Both are made from the same timber; the difference is visual: how many knots are allowed, how large they can be, how consistent the colour is, and how much natural variation the board may show. This guide explains which grade to use for a terrace, facade or large area, how much extra to order, and what changes during installation.

Quick comparison

CriteriaAB gradeBC grade
KnotsFew, smallMore, larger
ColourMore consistentGreater colour variation
Natural variationLess visibleMore visible
Best forVisible terraces, facades, furnitureLarge areas, utility buildings, walkways
Waste allowanceAbout 10%10–15%
PriceHigherLower

What are AB and BC grades?

AB and BC are visual quality grades. They describe how many knots, colour differences and other natural marks are allowed on a board. They are not strength classes: both are made from the same Siberian larch and kiln-dried (KD) to 16% ±2% moisture.

In other words, the grade helps you choose an appearance, not change the wood's properties. If a project needs a specific strength class (C18, C24), that is specified separately and agreed with a structural engineer.

AB grade

AB has few knots and they are usually small. The colour is more consistent and there is less visible natural variation. That makes AB the better choice where the surface is seen up close: a house terrace, balcony, representative facade, outdoor furniture or decorative details.

AB does not mean a board with no knots or colour variation at all – wood is natural. It simply looks more uniform than BC.

BC grade

BC allows more and larger knots, plus greater colour and grain variation. That is not a defect: knots are a natural part of the wood, and knot areas are often denser. BC is often chosen for large areas, utility walkways, fences, sheds or projects where a more economical appearance is acceptable.

If the terrace is large and its surface will not be viewed closely all the time, BC can be a rational choice. If you want a more uniform look near the house, choose AB.

Where do knots come from?

Knots are the bases of branches that grew into the trunk. In a sawn board they appear as darker, denser circles or streaks. The larger the knot and the closer it is to the board surface, the more visible it is. This is natural wood structure, not a production defect. Growing conditions, the part of the trunk and the sawing pattern determine how many knots end up in a particular board, so no two boards have identical grain.

Why is AB more expensive?

AB requires more selection: boards with fewer knots and more consistent colour are picked from the batch. BC allows greater natural variation, so more boards make the grade and the price is lower. When comparing quotes, look beyond €/m²: grade, thickness, width, length, moisture, whether VAT is included, how many boards the project needs and what waste allowance is included.

Does the grade affect strength or service life?

Not automatically. Strength depends on the timber, board dimensions, moisture, joist spacing and the whole structure. AB and BC are visual grades, so you cannot say an AB board will always carry more load than a BC board of the same section.

Service life is driven mainly by ventilation, fixings, protection from direct ground contact and maintenance. Knots can affect machining, how evenly a finish is absorbed, or the local appearance, but a well-built BC terrace can still last a long time.

Where to use AB and BC

  • Visible terrace near the house: AB – more consistent colour and fewer knots.
  • Large terrace or utility walkway: BC – less sensitive to the appearance of individual boards.
  • Representative facade: AB. A utility building or fence may be fine in BC.
  • Outdoor furniture and details: AB if the surface is seen up close.
  • Structural beams: these use a separate ABC grade; do not confuse it with the AB/BC visual grade of boards.

Common mistakes

  • Choosing BC for a showpiece terrace and expecting an AB appearance.
  • Ordering AB without waste and running short after cutting.
  • Judging boards from one photo – lighting and angle change the look significantly.
  • Not checking moisture and not letting the boards acclimatise on site.
  • Mixing grades in one visible surface.

Installation and finishing

The installation principles are the same for both grades: leave a 5–8 mm gap between boards, keep air moving under the terrace, fix to joists and use stainless-steel screws. Use two screws per board at every joist.

In BC, knot areas can be harder, so test on an offcut before drilling and avoid drilling straight into a large knot. Seal cut ends so water cannot enter the timber. If you plan to oil the terrace, test on a small area first: knots may absorb the finish slightly differently from the surrounding wood.

Maintenance by grade

The principles are the same for both grades: ventilation under the terrace, a clean surface, and timely removal of leaves and debris. If you want to keep the warm colour, oil with an outdoor oil that contains UV protection. In BC, larger knots may become more visible after a few years, especially if the terrace is not oiled. That changes the appearance, not the structural requirements.

Is AB worth the extra?

If the terrace is seen every day, sits next to the house or is used for entertaining, AB usually justifies the price. If the area is large, utilitarian or not the main visual focus, BC can be the more rational choice. The best decision is to see both grades in person or ask for photos of the actual batch.

How much extra should I order?

For AB, about 10% waste is usually enough for cuts and defects. For BC, plan 10–15% because some boards may need trimming around larger knots or selecting for the more visible areas.

Example: for a 20 m² terrace with 24×140×4000 mm boards and a 6 mm gap, one board covers about 0.584 m². 20 ÷ 0.584 ≈ 34.25, so you need about 35 boards. Add 10%: about 38 boards; add 15%: about 40 boards.

How to check a delivery

When the boards arrive, check moisture, knot content and colour against the grade you ordered, and look for mechanical damage. Before installation, leave the boards on site for at least 2–3 days so they can acclimatise. Store them flat on supports, not on the ground, protected from rain and direct sun but with air circulation.

Frequently asked questions

Is AB grade stronger than BC?

No. AB and BC are visual grades, not strength classes. Both are made from the same Siberian larch; strength depends on dimensions, moisture, joist spacing and the structure.

Which grade should I use for a terrace?

Choose AB for a visible terrace close to the house: fewer knots and more consistent colour. BC suits large areas, utility walkways or projects where a more economical look is acceptable.

How much extra should I order?

For AB, about 10% waste is usually enough. For BC, plan 10–15% because some boards may need trimming around larger knots.

Are knots a defect?

No, they are a natural feature of the wood. AB has few small knots; BC allows more and larger knots. They can be more visible, but that does not make the timber unsuitable.

Can BC be used for cladding?

Yes, if the facade is not a showpiece or if colour and knot variation are acceptable. AB is the usual choice for a visible house facade.

Does the grade change maintenance?

The principles are the same: ventilation, a clean surface and periodic oiling if you want to keep the colour. Knots can absorb finish slightly differently, so test on an offcut first.

Links

Decking boards (catalogue) · AB 24×140×5100 mm board · BC 24×140×2500 mm board · Installation guide · Larch vs pine vs thermowood